Gears and Gear Selection
Whether you use them all or not, you likely have many gears on your bike so that you
can exert nearly the same amount of pedaling effort whether you’re riding up a hill,
down a hill, or on level ground at a wide range of speeds.
For good efficiency and low impact on your knees, most people find a pedaling cadence
of 75-95 revolutions per minute (rpm) to work for them. You can determine your cadence
by manually counting how many times one pedal goes around in a minute. When you are
maintaining a steady cadence, the bike will travel different distances depending on
the gear you select. For example, when a bike is in high gear, each revolution of the
pedals propels it a long distance-perhaps 25 feet or so - but pedaling effort is very
high. When the bike is in low gear, each revolution propels it only a short distance
- perhaps as little as five feet - but the pedals are easier to turn.
If your bike has three chainrings, you will do much of your riding in the middle one.
Most of yourshifting will be done with your right hand to use the rear derailleur to
find a comfortable gear. Remember to shift with derailleurs only when pedaling.
If the change in terrain is pronounced, you will need to shift the front derailleur as
well. Move it onto a smaller chainring (toward the bike) for a lower gear and onto a
larger chainring (away from the bike) for a higher gear. Use the shifter at your left
hand to move the chain while pedaling. Remember, moving the chain towards the bike makes
it easier to pedal and moving the chain away from the bike makes it harder to pedal.
Riding confidently and competently in traffic sends the message that you belong in the
roadway. One of the best ways to do this is to start quickly and confidently. You do
this by starting with one pedal in an up position, then putting all your weight on the
pedal to launch you and your bike across the intersection. As you are pushing on the
pedal, ease back onto the saddle.
To stop smoothly and evenly, use both brakes with more pressure on the front one. Just
as you come to a complete stop, turn the handlebars a little bit away from the side you
want to step down on. The bike will lean to that side so you can step down.
Steering a Straight Line
If started in motion carefully, a bicycle without a rider can coast all the way across
a parking lot before it eventually falls down. Your job is to use small motions to steer
the front wheel as little as possible so as to keep the bike directly under your center
of gravity. So look up and let the bicycle work for you.
If the bike leans to the right, the front wheel will tend to steer itself to the right,
and if the bike leans to the left, the wheel will steer to the left, assuming no force
is applied to the handlebar. On a bike that is moving and upright, the caster effect
keeps the wheel lined up in the direction of motion.
When riding in traffic, you need to be predictable and communicate with drivers when you
are going to change your speed or roadway position. You can do this by looking around,
or scanning, and when it is safe, signaling your intentions.
Scanning is the act of looking over your shoulder. You do it to check for overtaking
traffic or to see that you are clear before merging or changing lanes. This is a skill
that you’ll need to be proficient at so you can keep the bicycle moving in a straight
line while you are looking back. Practice looking over each shoulder until it becomes
second nature and you are able to maintain a straight line of travel while looking
A large part of being predictable in your actions on the road is letting others know
what you plan to do before you do it-hand signals are a vital communication tool.
Scanning behind you while riding in traffic may act as a secondary signal to motorists
that you plan to change your position on the roadway.
The right-turn signal has historically been the left arm outstretched and bent upward
at the elbow. When used by a cyclist, this signal may be difficult for motorists to see.
Some states now allow the outstretched right arm to indicate a right turn. Always use
hand signals when turning, changing lanes and even when changing position in a given
lane. Motorist will appreciate the courtesy and respond in kind.
Be sure to stop signaling well before entering the intersection. At this point, it is
more important for you to have both hands on the handlebar for maximum control and
Reprinted from League of American Bicyclists "Smart Cycling/Traffic Skills 101".
For more information on good cycling tips, see
How You Can Ride Better.
For more information about the League of American Bicyclists, visit
their web site, www.bikeleague.org,
or e-mail them at firstname.lastname@example.org.